The general waterproof slurry produced by Fujian Ningde Xinjian Gong Waterproof Material Technology Co., Ltd. uses the penetration mechanism of permeable crystalline materials into concrete, combining the unique adhesion, water retention and water retention properties of polymer emulsion with concrete and cement mortar base layers. With a certain degree of flexibility, it forms an integrated composite waterproof material that has a penetrating and crystallizing effect on the concrete capillary pores, and at the same time forms an integral and consistent dual waterproofing function on the base surface. This product implements the Type I technical indicators of the national building materials industry standard "Polymer Cement Waterproof Slurry" drafted by our company. [Product Features]
. Resist high hydrostatic pressure and have the waterproof function of negative water surface
. Can cover fine cracks and resist extremely slight shocks
3. Can be used on wet substrates Construction on the surface and used in conjunction with a variety of flexible waterproof materials
. Can be constructed on complex and rough base surfaces
. After the waterproof layer is applied, the concrete can still maintain good air permeability
. Can be effective Avoid efflorescence phenomenon
. After the slurry dries, it can be directly pasted onto ceramic tiles or plastered for leveling
. After drying, the coating becomes a semi-rigid and tough coating, resistant to wear and impact
.The coating can inhibit the growth of mold and prevent moisture and salt from contaminating the surface
.Non-toxic and harmless, can be directly used in drinking water pools and fish ponds
.Suitable for long-term immersion in water occasion.
[Scope of application]
.Indoor and outdoor cement concrete structures, cement plastering, brick walls, lightweight brick wall structures
.Floor walls and floors, kitchens, bathrooms, planters, floors, Garage
3. Edible pools, swimming pools, fish ponds, sewage treatment tanks
. Apply to the substrate before paving stone, ceramic tiles, wooden floors, wallpapers, and gypsum boards
. As a pre-installation Wiping the bottom can prevent moisture and salt contamination.
[Construction Technology]
Base surface treatment: The base surface must be solid, clean, flat, moist, free of oil, and free of floating ash. If there are pores, cracks and other defects on the base surface, use cement mortar to repair and smooth the yin and yang in advance. Use a spatula to trim the corners into half-round corners.
Ingredients: Pour the additives into the container according to the mixing ratio, then slowly pour the powder into the additives, and at the same time stir thoroughly until it is particle-free and uniform, and it is ready for use. Keep intervals during use. Stir regularly to prevent stratification and precipitation.
Construction: Apply directly to the base surface with a brush or roller brush, use even force and do not miss the brush. If it is used for moisture-proofing, only one layer is required for waterproofing, and two to three layers are required. When the first layer dries to the point where it is no longer sticky (usually it takes - an hour), the second layer can be applied. The painting directions of each two layers should intersect perpendicularly.
Coating protection: After the slurry construction is completed, necessary protection must be carried out on the coating before it is completely dry, including prohibiting pedestrians, rain erosion, exposure, damage by sharp objects, etc. A special protective layer is required.
Coating maintenance: It is recommended to cover the coating with a damp cloth or spray water to maintain the coating hours after the coating is applied. Generally, the drying time will be longer in places with high air humidity and poor ventilation, and vice versa. In environments with particularly poor air circulation, mechanical ventilation methods can be used to speed up drying for the sake of project progress.
Construction temperature: Suitable for use in ℃-℃ environment.
Reference dosage: Moisture-proof floors and exterior walls. Bathrooms, pools, and negative waterproofing under hydrostatic pressure. Negative waterproofing under high hydrostatic pressure.
【Packaging, Storage and Transportation】
. Packaging: (powder + additive) / set, (powder + additive) / set.
. When storing products, they should be ventilated, dry, and protected from direct sunlight. The storage temperature should not be lower than ℃. Unopened products have a shelf life of one month.
3. The product is made of non-flammable and explosive materials and can be transported as general cargo. During transportation, prevent freezing, rain, exposure, squeezing, and collision, and keep the packaging intact.
Universal k11 waterproof slurry